Skip to content
circuia
Editor

The country sets the standard for new projects and the currency.

Guide · Permit drawings · United States

How to draw an electrical plan for a permit (US homes, NEC 2023)

A residential electrical permit drawing is a floor plan showing every receptacle, switch, lighting outlet and smoke / CO alarm, plus the panel location and size, a circuit list (panel schedule) and, when the service changes, a load calculation. Requirements are set by your local permit office (the AHJ), which reviews the plan against the NEC edition it has adopted, then inspects the work at rough-in and final.

Updated on Last checked NEC (NFPA 70) 2023

Key facts

  • 01The AHJ (city or county permit office, sometimes the state) decides what the drawing must show; there is no single national permit form.
  • 02Typical contents: floor plan with receptacles, switches, lights and smoke / CO alarms, panel location and size, panel schedule, symbols legend, and a load calculation for a new or upgraded service.
  • 03The plan should already respect the NEC layout rules: receptacles within 6 ft of any point along a wall, every 24 in on countertops, one within 3 ft of each bathroom basin (210.52).
  • 04One-family dwelling service: at least 100 A (230.79(C)), outdoor emergency disconnect (230.85) and surge protection (230.67) since NEC 2020.
  • 05Inspections: rough-in (boxes, cable, grounding, before insulation and drywall) and final (devices, GFCI / AFCI, panel directory, alarms).

Start with your permit office, not with the code book

Many permit offices publish a residential electrical checklist or a sample drawing. Read it first: it tells you the paper size they accept, whether they want the panel schedule on the same sheet, whether a load calculation is needed for your scope, and whether they accept a homeowner's own drawing. The edition that applies is usually tied to the date of the permit application (Massachusetts and Minnesota both work that way), so a project filed before a changeover may stay on the older edition.

What permit offices typically ask for

Typical contents of a residential electrical permit drawing
ItemWhat to showRelated NEC / IRC section
Floor planEvery room, labeled (bedroom, kitchen, bath, hallway…), with doors and fixed cabinets; dimensions in feet and inches—
ReceptaclesWall receptacles (6 ft rule), countertop receptacles (24 in rule), bathroom, outdoor front and back, laundry, garage, hallways of 10 ft or more210.52
GFCI and AFCIWhich receptacles and circuits are GFCI, AFCI or dual-function210.8(A), 210.12(A)
Switches and lighting outletsA wall-switched lighting outlet in every habitable room, kitchen, bathroom, hallway, stairway, attached garage and outdoor entrance; 3-way switches where you control from two places210.70(A)
Smoke and CO alarmsEach bedroom, outside each sleeping area, each story; hard-wired, interconnected, battery backup; CO alarms where there are fuel-burning appliances or an attached garageIRC R314 / R315
PanelLocation, main breaker size (100 / 150 / 200 A), working space; not in a bathroom or clothes closet110.26, 240.24, 230.79(C)
Panel scheduleEvery circuit: number, breaker size and poles, wire size, what it feeds408.4
Load calculationFor a new service, a service upgrade or large added loads (EV charger, heat pump)220.82 / 220.83 (Article 120 in NEC 2026)
Symbols legendWhat each symbol on the sheet means—
Not every office asks for everything: a small remodel may only need the floor plan and a circuit list. Source: docs/norms/us-nec.md § 14, from AHJ publications and trade summaries.

Step by step: drawing the plan

  1. Draw the rooms to scale. Walls, doors, windows, fixed cabinets and countertops. Label every room by its use: the NEC rules depend on it (a bedroom needs AFCI, a bathroom needs GFCI and its own 20 A circuit).
  2. Place the receptacles. Walk each wall: no point along the floor line more than 6 ft from a receptacle, counting any wall space 2 ft wide or more. On kitchen countertops, no point more than 24 in from a receptacle. One within 3 ft of each bathroom basin, one at the front and one at the back of the house, one per garage bay, one in the laundry area, one in each hallway 10 ft or longer.
  3. Add lighting outlets and switches. At least one wall-switch-controlled lighting outlet per habitable room, kitchen, bathroom, hallway, stairway, attached garage and outdoor entrance (210.70(A)). In habitable rooms a switched receptacle may stand in for the light, not in kitchens and bathrooms. Show 3-way switches at both ends of halls and stairs.
  4. Place smoke and CO alarms. One in each bedroom, one outside each sleeping area, one on each story including basements. Note that they are hard-wired with battery backup and interconnected.
  5. Show the dedicated appliances. Range, dryer, water heater, dishwasher, disposal, microwave, HVAC equipment and any EV charger, with their voltage (120 V or 240 V).
  6. Group everything into circuits. At least 2 × 20 A small-appliance circuits for the kitchen and dining area, a 20 A laundry circuit, a 20 A bathroom circuit, a 20 A garage circuit, general lighting and receptacle circuits, then the 240 V two-pole circuits.
  7. Size wire and breakers. Copper 14 AWG on 15 A, 12 AWG on 20 A, 10 AWG on 30 A (240.4(D)); NM-B cable at its 60 °C ampacity (8 AWG on 40 A).
  8. Fill in the panel schedule and, if the service changes, the load calculation.
  9. Add the legend, title block and notes: address, owner, who prepared the drawing, NEC edition, scale.

The receptacle rules are explained in detail in NEC 210.52 receptacle spacing and the kitchen ones in kitchen countertop receptacle requirements. For protection by room, see GFCI and AFCI requirements by room.

Electrical plan symbols permit reviewers expect

US residential plans traditionally use the ANSI Y32.9 family of symbols (also found in NECA and National CAD Standard sets). Offices differ in how strict they are, and drawings by hand or from different software vary. What every reviewer expects is a legend on the sheet, so that no symbol needs guessing.

Common symbols on a residential electrical plan
DeviceUsual symbolNotes
Duplex receptacle (120 V)Circle with two short parallel linesTamper-resistant everywhere in a dwelling (406.12)
GFCI receptacleReceptacle symbol labeled GFCIOr note which receptacles are protected by a GFCI breaker or an upstream GFCI receptacle
Weather-resistant outdoor receptacleReceptacle symbol labeled WP or WRIn-use (bubble) cover in wet locations (406.9)
240 V receptacleReceptacle symbol with the NEMA configuration (e.g. 14-30R dryer, 14-50R range)On a two-pole breaker
Single-pole switchSMounted about 48 in to center (practice, not a code value)
Three-way switchS3Two of them control one light from two places
Ceiling lighting outletCircle (often with an X or a letter for the fixture type)Dashed line to the switch that controls it
Smoke alarm / CO alarmLabeled symbol, e.g. SD and COShow the interconnection in a note
Panel (load center)Rectangle with its ratingMain breaker size, location, working space
Conventions vary by office and by drafter: the legend on your sheet is what counts.

Panel schedule and load calculation

The panel schedule (circuit directory) lists every circuit by number with its breaker rating, number of poles, wire size and what it serves. The NEC requires the directory in the panel to identify every circuit by its purpose or location, spares included (408.4), so the drawing and the finished panel should match. A template is in panel schedule template.

A load calculation is usually requested when you install a new service, upgrade one or add large loads to an existing home. For a one-family dwelling, the NEC optional method (220.82, renumbered 120.82 in NEC 2026) takes 3 VA per ft² of floor area, 1,500 VA per small-appliance and laundry circuit and the nameplate of fastened-in-place appliances, counts the first 10,000 VA at 100 % and the rest at 40 %, then adds the heating or air-conditioning load. Divide by 240 V to get the service size. Existing homes use 220.83. Details and an example: residential load calculation (NEC 220).

  • Service for a one-family dwelling: 100 A minimum (230.79(C)); 200 A is the common choice for a new house.
  • Outdoor emergency disconnect, readily accessible and marked, for one- and two-family dwellings (230.85, NEC 2020 and later).
  • Surge protective device (Type 1 or Type 2) in or next to the service equipment (230.67).
  • Working space in front of the panel: 30 in wide, 36 in deep, 6.5 ft high (110.26); never in a bathroom or clothes closet (240.24).

Rough-in and final inspection: what the inspector checks against your plan

Rough-in (before insulation and drywall)

  • Boxes where the plan shows them (receptacle spacing, countertop, bathroom, outdoor, garage, hallway), box fill (314.16), fan-rated ceiling boxes where a fan goes (314.27(C)).
  • NM cable secured within 12 in of boxes and every 4.5 ft (334.30); nail plates where cable is less than 1¼ in from the stud edge (300.4(A)).
  • Neutral at switch locations (404.2(C)); handle ties on multiwire circuits; wire sizes matching breakers.
  • Grounding electrode system, bonding of water and gas piping, service and emergency disconnect, surge protection.
  • Boxes for the smoke and CO alarms.

Final

  • Devices installed: tamper-resistant receptacles, weather-resistant receptacles with in-use covers outdoors, GFCI / AFCI / dual-function protection where required (tested with the test button).
  • Panel: complete circuit directory, working space clear, no double-tapped breakers, neutrals and grounds separated in subpanels.
  • Lighting outlets switched; smoke and CO alarms interconnected and powered.
  • Load calculation and appliance nameplates (range, dryer, water heater, HVAC, EV charger) available where the office asks for them.

After the final inspection (or the service inspection), the utility sets the meter or releases the service.

Homeowner permit or electrical contractor?

Many jurisdictions allow a homeowner to pull a permit for their own single-family home and do the work themselves; rules vary by state and city, and some limit it to an owner-occupied home or require the owner to pass a short test. Elsewhere, only a licensed electrical contractor may pull the permit. When a contractor does the job, they usually prepare the drawing as part of the permit application. Ask your permit office which case applies before you buy materials.

Either way, the drawing is the document the plan reviewer and the inspector compare the work against. A clear plan with a legend and a matching panel schedule saves corrections and re-inspections.

Drawing the permit plan with Circuia

In Circuia you draw the rooms on a grid in feet and inches. Equip the rooms places receptacles by the 210.52 rules (6 ft wall rule, 24 in countertop rule, 3 ft from basins, hallways of 10 ft or more) and a switched lighting outlet in each room. Automatic wiring builds the branch circuits: 14 AWG / 15 A lighting, 12 AWG / 20 A receptacles, the two 20 A small-appliance circuits, the 20 A bathroom circuit and 240 V two-pole circuits for the range, water heater and EV charger. The check flags missing GFCI / AFCI protection, wire sizes that don't match breakers and other issues, and reminds you of smoke alarms and service requirements.

The PDF export on Letter paper contains the floor plan with its symbols and legend, the panel schedule (circuit directory), the single-line diagram and the materials list. You can send a share link to the homeowner. Circuia does not yet compute the load calculation, and its plan symbols are not the ANSI Y32.9 set, so keep the legend on the sheet and attach your load calculation separately. Drawing and checking are free; the Project Pass ($45 one-off, plus sales tax) adds the PDF exports and materials list for one home.

Start a US plan in the editor, free, in your browser.

Common mistakes

  • Drawing before checking what your permit office actually asks for (paper size, load calculation, who may prepare the drawing).
  • Leaving rooms unlabeled: GFCI, AFCI and circuit rules depend on whether a room is a kitchen, bathroom, bedroom or garage.
  • Forgetting the outdoor receptacles at the front and back, or the one in a hallway 10 ft or longer.
  • Showing smoke alarms in bedrooms only, without the one outside the sleeping area and on each story.
  • Putting the panel in a clothes closet or a bathroom.
  • A panel schedule that doesn't match the plan's circuit numbers.

Frequently asked questions

What does an electrical plan for a permit need to show?

Typically a floor plan with every receptacle, switch, lighting outlet and smoke / CO alarm, the panel location and size, a circuit list or panel schedule and a symbols legend. When the service is new or upgraded, offices usually ask for a load calculation too. Requirements vary: your local permit office (the AHJ) publishes what it wants, sometimes as a checklist or sample drawing.

Can I draw my own electrical plan for a permit?

Often yes. Many jurisdictions allow a homeowner to pull a permit for their own single-family home and submit their own drawing; rules vary by state and city. Some offices require the drawing to be prepared or stamped by a licensed electrician, especially for larger projects. Ask the permit office before you start, and expect a rough-in and a final inspection either way.

Which NEC edition should my plan follow?

The one your jurisdiction has adopted, usually tied to the permit application date. The 2023 NEC is the most widely adopted edition; Massachusetts, Minnesota, Texas and Washington have moved to 2026, and some places are still on 2020 or older, often with local amendments. The permit office can tell you the edition and its amendments.

Do I need a load calculation for a permit?

Usually when you install a new service, upgrade the service or add large loads such as an EV charger or heat pump to an existing home. For a one-family dwelling the NEC optional method (220.82, 120.82 in NEC 2026) counts 3 VA per ft², the small-appliance and laundry circuits and fastened appliances, the first 10,000 VA at 100 % and the rest at 40 %, then adds heating or cooling.

What are the rough-in and final inspections?

The rough-in inspection happens after boxes and cable are installed and before insulation and drywall: the inspector checks box locations against the plan, cable support, wire sizes, grounding and bonding. The final inspection happens once devices are installed: GFCI and AFCI protection, tamper-resistant receptacles, the panel directory, switched lighting and interconnected smoke alarms.

Does Circuia produce a permit-ready drawing?

It produces a floor plan with symbols and legend, a panel schedule, a single-line diagram and a materials list on Letter paper, checked against its US rules pack, which has not been reviewed by a US master electrician. Whether the drawing is accepted is up to your permit office; it does not compute the load calculation yet and does not replace a licensed electrician or the inspection.

Design aid

Design the installation with this country's rules

Draw the home or describe it to the AI: Circuia places the points, checks the country's rules in real time and generates the consumer unit, single-line diagram and bill of materials.

Open a free sample plan with these rules

Written by

Circuia team

Written by the Circuia team from the sources listed and from the editor's rules pack for this country: the values in the tables are the ones Circuia uses.

Published · updated